Model: 8-5V24V-D Channels: 8 Channel Input: NPN or PNP, 5V or 24V Level of Orthopedic Signal Output: NPN 5V or 24V Square Wave Signal Size: 11 * 9 * 5cm / 4.3 * 3.5 * 2in Weight: 170g (approx.)
8 input signals can receive NPN or PNP signal levels.Independent separation, input levels have positive and negative points.IN1+ indicates the first signal input is positive. IN1- refers to the negative first signal input. IN8+ indicates that the 8th signal input is positive. IN8- refers to negative 8th signal input. The input signal is compatible with signals of 24V, 5V, 12V, 3.3V levels.Input level of 5V or 24V is set by DIP switch. The numbers 1-8 on the DIP switch represent the settings of 1-8 channels.ON is input 5V level, OFF is input 24V level.The output 5V level is a push-pull output after Schmidt waveform algebraic amplification and supports NPN interface.The maximum output current is 10MA. Each 5V level output port is 5V 15V 2 to 5V 8.Output 24V level is NPNOC output. 24V level output ports are 24V 124V 2 to 24V8. The 24V output must be connected to the pull up resistor 10K connected to the V + or 24V power source on the board.Only support AC and DC power supply.If you only need 5V level, the default is 24VDC.The power supply voltage can be between 7-35V DC-5-24VAC. If you need to output 24V level, the power supply voltage is between 24-35VDC, 18-24VAC.The power input is not separated from positive and negative so you can connect it to a power source without burning issue.High-speed 10M bandwidth optocoupler is used for signal isolation transmission, followed by signal shaping and amplificationThe integrity of the system signal is guaranteed and will not warp the pulse waveform
A.35MM Standard Industrial Electrical Control Board Guide Rail Installation MethodB. You can also use the screws and copper poles to attach to the bareboard PCBA.
|
|
|
---|---|---|
Support NPN interfaceThe maximum output current is 10MA.Each 5V level output port is 5V 15V 2 to 5V 8. |
Output 24V level is NPNOC output24V output is OC output (NPN open circuit output). If you use the meter to measure the output, you will need to add pull-up resistance. Pull up resistance is usually 10KR.24V level output ports are 24V1, 24V2-24V8. The 24V output requires you to connect the pull up resistor 10K to the positive terminal of the V + or 24V power supply on the board. |
Support AC and DC power supplyThe default is 24VDC. When only 5V output is required, the power supply voltage can be adjusted from 7-35V DC to 5-24VAC. If you need to output 24V level, the power supply voltage is 24-35VDC - 18-24VAC.The power input is not separated from positive and negative and there is no problem of damage to the module due to reverse power supply. |
Mainly used for interface matching between PLC or MCU and other circuits.Signal level transformation of external circuits or level transformation between other control circuits.The module can convert 8 signals at the same time. It uses a 10MHZ bandwidth isolation chip. Effectively ensure signal speed and integrity
1. Input 5V level signal will be converted to 24V level signal.Or input a 24V level signal and convert it to a 5V level signal.2. Switch the signal from 5V level to 5V or 24V to 24V level, and you can separate the input signal from the output signal through the optocoupler.This allows you to change and improve the circuit anti-interference ability.3.Integrated amplification circuitry provides strong driving ability4. Compatible with common cathodes or common anode input connections, meeting European and Japanese PLC interface standards.5. Compatible with AC and DC input power interface with power indicator.6. If you choose the output to 24V level, it is NPN OC output, the maximum load capacity is 1A. 24V output is OC output (NPN open circuit output).If you use the meter to measure the output, you will need to add pull-up resistance.Pull up resistors generally use 10KR for FF.7.7. To convert the signal to 24V level, you need to control the power of the power input interface to 24V. 8. To convert the signal to 5V level, you need to control the power supply input interface from 7-35V.