[Electric Impact Wrench + Air Compressor Set]

[Single piece only]

[Electric Impact Wrench + Tire Stopper Set]

Product Description

The nut will loosen and collapse smoothly with the same movement as an air impact.
Easy to hold, easy to work with.
Powerful rotational torque to turn the nut
Time-saving and time-consuming work smoothly.

Indications

This product is used for removing and temporarily tightening the wheel of the car when removing and removing the wheels. Always use a torque wrench when tightening this item. Please do not use for anything other than the intended purpose.
Please read and understand the instruction manual carefully before using this product. The instruction manual contains important considerations. Use without following the description will lead to serious accidents.
Keep away from children while working.
Please keep your hands and face away from the rotating part of the socket while in use. This may cause injury. ● There are products that cannot be used with this product due to the guidance of the wheel manufacturer and wheel nut manufacturer, so please follow the instructions provided by each manufacturer

From the Manufacturer

The nut loosens and tightens smoothly with the same movement as an air impact.

Easy grip makes it easy to work with.Powerful rotating torque to turn the nut.Work smoothly in no time.

• Input Voltage: AC100V
• Tightening torque: 250 N·m Tightening time 2 seconds (without splice cord)
• Power cord length: about 2.1m
• Current: 3.5A
• Rotational Speed: 0-2900/min
• Number of beats: 0-3100min-1
• Product Size: Approx. W 3.1 x H 8.1 x D 11.4 inches (80 x 205 x 290 mm).
• Weight: Approx. 4.4 lbs (2.1 kg) (excluding cords and sockets).

The power of the motor can be removed and detached while the "behind". The wheel nut is easy to put on and take off.Since it is a continuous hit, it can also be used to save time when changing tires.	Product Specifications Accessories: 0.75 inch (19 mm), 0.8 inch (21 mm) deep socket, blow case, carbon brush x 2 (spare). Drive: 0.5 inches (12.7 mm)	Work by yourself = IY

How to use

Part names and standard accessories	Push the forward and reverse switch as shown in the picture to change the direction of the rotation. Pull the trigger on the switch and turn the motor.Release to stop	Jack up Check the jack point and jack up until the jack stand is under the position of the vehicles jack set.	Jack down Jack down until the jack stand holds the vehicle.

Move Floor Jack In the event of an accident, the tire was removed under the body (design side upward), lower the jack arm, and move the floor jack.	Wipe off wheel grime Wipe away dirt from the wheel contact with a damp cloth.	Install replacement wheels Install the replacement wheels, turn the wheel nut by hand and tighten it using this product.	Remove Jack Stand

	FT-09P	FT-10P	FT-50P
Input Voltage	DC12V	DC12V	AC100V
Tightening Torque	Max340N·m	Max340N·m	250 N·m Tightening Time 2 Seconds (without splice cord)
Power Cord Length	Approx. 13.4 ft (	Approx. 13.4 ft (	Approx. 6.6 ft (2.1 m).
Maximum Current	13A	13A
Fuse Capacity	15A glass tube (inside power plug)	15A glass tube (inside power plug)
Product Size:	Approx. 8.3 x 7.9 x 3.1 inches (210 x 200 x 80 mm).	Approx. 8.3 x 7.9 x 3.1 inches (210 x 200 x 80 mm).	Approx. W 3.1 x H 8.1 x D 11.4 inches (80 x 205 x 290 mm).
Weight	Approx. 3.3 lbs (1.5 kg) (excluding cords and sockets)	Approx. 3.5 lbs (1.6 kg) (excluding cords and sockets)	Approx. 4.4 lbs (2.1 kg) (excluding cords and sockets).