Feature
●Small sensor switch unit with motion sensor and brightness sensor, which has been implemented with an extension cord for easy installation without wiring work. You can turn lighting fixtures such as bulbs, electric stands, floodlights, and other electrical products with AC cord such as circuitors and fans with motion sensor switches to turn on power in response to human movement. Just plug this male plug into an AC outlet such as a wall and plug in an AC plug into a female socket for light equipment, and it does not require any qualification for an electrician. Note: Devices up to 100 W can be connected. Trouble connecting devices with a power consumption exceeding 100W is not covered under warranty. Please check the power consumption of the device you want to attach. (Electric heaters, electric kotatsu, electric blankets, etc. are strictly prohibited)
●The dimensions of the sensor are 2.4 inches (60 mm) wide x 2.2 inches (55 mm) deep x 1.6 inches (40 mm) tall. It is small enough to install anywhere. The sensor part can be fixed to the wall with the 2 screws included. The cable length to the end of the plug is approximately 19.7 inches (50 cm) on the male AC plug side and female AC socket side. The cable is soft and easy to handle. The plug is 2 pin male and female end
●Compatible Power Supply: AC 100V, 50/60Hz, Supports devices up to 100W power consumption. The sensor can be adjusted with 3 knobs. 1. Motion sensor detection distance: minimum 6.6 ft (2 m) to maximum 26.6 ft (8 m), 2. Power interval: about 10 seconds to 7 minutes (power is off if no person is moved alone), ambient brightness when the power is turned ON: about 10 to over 2000 lux. It will automatically extend when it detects human movement again during power and continue to work while people stay moving within the sensing area. (If people do not move, power will be disconnected)
●Japanese manual included (refer to the product description below). Sensor Body Country of Manufacture: China (our designated factory). Warranty: 1 year (Niigata Prefectures Ryudo Co., Ltd.) Japanese staff inspects the product at the time of arrival and will provide immediate and careful support) [Important] IP44 equivalent and is not waterproof. For outdoor use, you can use it on the eaves that do not get exposed to rain, but it cannot be used in places exposed to rain. When using outside eaves, please make sure to wrap vinyl tape around the cable and outlet connections to prevent water from entering. Also, make sure the unit is installed so that the adjustment knob is facing downward. If water gets injected from the crimp and connection parts, it may be shortened and broken. Please note that we will not be able to support any of these cases
●Because the motion sensor detects changes in ambient temperature and operates, it has the following characteristics: Even animals other than humans have heat so they can detect them. As the ambient temperature exceeds 30 degrees, the sensitivity will decrease as the temperature difference between the human body. It will not work if there is a shielding object such as walls, glass, etc. It may react to the exhaust heat of a car running on a nearby road. It can detect temperature differences due to wind convection such as heaters, and it may light up even if there is no human. This product is a triac dimmer
●(Standby power is approximately 50 yen per year) The standby power of this product is effective at 0.2 W (actual measured in the lud). Calculated at kW 27 yen 4.8 W per day, and 144 W per month. Considering the wasted power due to forgetting to turn off the connected product, the energy saving effect is very large
●When you are planning to use it by connecting it to an air purifier or high-performance fan: It can be used with a circular or fan that turns on and off using a mechanical switch, and when the device is turned on and unplugged and unplugged, without having to press the power switch again. It is controlled by a multi-functional electronic switch such as an air purifier. If the device is turned on and unplugged and unplugged, the power switch will not be turned on if the device is turned on
Description
