Feature
●3-in-1 Wall Detector for Detecting Wood, Metal, and Electrical Wire: You can detect the edges and centers of invisible parts (wood, metal, wire) on the back of wall materials and ceiling materials. Useful when installing curtain rails, shelves, picture frames, handrails, and earthquakeproof hardware
●5 Detection Modes: 3 student modes (detection depth: 0.5, 1.0, 1.5, 1.5 inches (13, 25, 38 mm), metal mode (detection depth: 2.4 inches (60 mm), wire mode (detection depth: 2.0 inches (51 mm)). In studded mode, metal and wood can be detected, and only metal can be detected in metal mode, so you can tell if the studs material is wood or metal
●3 Stage Post Detection: You can set the student detection mode in 3 levels (0.5, 1.0, 1.0, 1.5 inches (13, 25, 38 mm). When looking for a stud, you can switch from shallow mode to deep mode to guess the depth of the studs, making it convenient for nails and drilling
●Warning: Prevents accidents from hitting the wire on the back of the wall: When you hit a nail or anchor, it will notify you when the AC wire is close (about 20.1 inches (51 cm) range) even when it is detected. You can also locate the position of the wire with the wire mode
●Backlit LCD Display and Buzzer Sound: The backlit LCD screen is bright and easy to see even in dark places, so you can see the results of finding both ends and the center at a glance. It also has a buzzer sound so you can check the results of detection
Description
Product Specifications
Detectable base material: Wood, metal, wire, compatible wall materials: Veneer, gypsum board and other batteries: 9V battery x 1; Material: Plastic automatic poweroff: 180 seconds: Approx. 6.4 x 2.7 x 1.2 inches (161 x 68 x 30 mm); Weight: 4.9 oz (140 g) (battery excluded); Operating temperature range: -29 °C to 666 °C)
|
|
|
|
|---|---|---|
|
3 student modes (detection depth: 0.5, 1.0, 1.5 inches (13, 25, 38 mm) The student detection mode can be set to 3 different levels than the depth.When looking for a stud, you can switch from shallow mode to deep mode to guess the depth of the studs, making it convenient for nails and drilling. |
Metal mode (detection depth: 2.4 inches (60 mm) In studded mode, metal and wood can be detected, but in the metal mode, only metal can be detected, so you can tell if the student is wood or metal. |
Wire Mode (Detection Depth: 2.0 inches (51 mm) You can locate the position of the wire in the wire mode. Warning power lines behind the wall The electrical warning mark will notify you when you are detecting any mode and the AC cable is nearby, to prevent accidents that may be hitting on the wire when you hammer nails or anchors. |
How to detect studs?
|
|
|
|
|---|---|---|
Step 1Default Press the scan button to reveal a single sign.When the single sign disappears and the buzzer sounds "pee" indicates that the default setting is complete.In order to maintain the measurement accuracy, please make sure to set the initial setting by the scan button before detecting it. |
Step 2Finding the end of the stud. Slide slowly, not off the wall.When you close to the end of the stud, it indicates the end of the stud. |
Step 3Find the center of the stud. When you close to the center of the stud, the "CENTER" will display and hear "pe".The bar increases when the single strength sign approaches the studs. |
Suitable for wall materials (or ceiling materials)
Do not use in the following conditions:
In rain or dripping, where water is affected by water, such as bathrooms, kitchens, and other areas where the interior is condensed when the wallpaper (cloth) glue is not dry (please dry one week after adhesive).
Do not use on wall materials such as:
Wall material with high moisture absorption (such as cotton walls) with uneven surfaces of 0.04 inch (1 mm) or more irregular surface density (such as sandy finishes), wallpaper with gold thread, gold foil, etc.
