Feature

●Rating: 3A 100V AC LED lighting compatible with 2-100W (but within 10 lights)
●Power consumption when off: Approx. 0.2 W (power consumption when on approx. 0.8 Wiring method: 4 wire installation location: Indoor (ceiling); Illumination function: With brightness sensor; Operating illumination: dark: Approx. 20 lux; Brightness: Approx. 80 lux; Confirmation (cut): No brightness; Operating retention time: Approx. 10, 30 seconds, 1, 3, 5, 5, 10, 10, 20, 20, 30, 30, 30, 30, 30 minutes, Output method: When loading or shutting off. : Triac control outputs during power flow: voltage relay contact output
●The heat-sensitive sensor switch will detect and operate at temperatures above 3 degrees Celsius in the detection area. When the load is turned on, the operating time will be extended by only the set time
●Do not wire a single switch, etc. on the power line of the sensor switch. When power is on, it will run erratic for about 40 seconds due to the initial state of the heat sensitive sensor
●[Handling Precautions] There may be cases where the detection motion is not activated, or the detection sensitivity is dull, but it is not a malfunction. 1. When people are stationary; 2. If the difference between the human body and surrounding temperature is within 3 degrees Celsius (3 degrees Celsius), such as in midsummer day; when the breaker is turned on, it will be unstable for about 40 seconds due to the initial state of the heat sensitive sensor. It will then be normal when it can be detected. Detection surface will decrease if the detection surface is contaminated. If it gets dirty, please wipe it off with a soft cloth. *Do not use chemical sugar powder, thinner, or detergent


Description

■Features
This sensor detects heat emitted by people and animals, and automatically turns on and off.
There are also rotary switches for heat sensitive sensor switches.

Manufacturer: JIMBO / Shinkboelectric
Series Name: Thermal Sensor Switch

Please note:
The connection to the child device is not polarity.
Up to 2 wires, total wire length up to 164 ft (50 m).
Please remove the terminal cover when connecting to the child device.
Child device wiring is AC 100 V. Please cut off the power circuit before wiring.
If the child wire is substrated to the ground it becomes unusable.
Also, there is a risk of electric shock.

This product requires installation by an electrician.
General consumers who do not qualify for installation and replacement work is not legal
If the wrong wiring or load side is short-circuited, overcurrent will damage the internal components, making it unusable to use.
Cannot be used with HID lamps (high intensity discharge lamps).
Please use incandescent lamps under 100 W per light. When the bulb is out of power, the internal components may interfere with a large current.
For safety, please do not connect to electric heating appliances.
When performing mega tests, please remove the device from the train.
(When measuring between wires and grounds, please remove the device from the train. )
Please test breakers on the load side before installing the equipment.
Break in an instant short circuit.
Do not wire a single switch, etc. on the power line of the sensor switch.
When power is on, it will run erratic for about 40 seconds due to the initial state of the heat sensitive sensor.
Cannot be used with special lighting fixtures built in electronic circuits.
(Built-in lighting fixture with delay timer, dimming function, wall switch, short on/off operation and switching on and off, remote control function)

Precautions for Installation Locations:
Do not install in the following locations:
1. Where heating and cooling equipment such as air conditioners and stoves enter the detection range
2. Close to cooking equipment such as stoves, and places under hot air and steam.
3. Location where incandescent lamps and lighting fixtures are nearby (within 1m from the fixture)
4. Location under indirect light due to reflections
5.Where swinging or moving objects are placed
(where there are effects of shadows, leaves and leaves caused by swinging curtains and curtains)
6. Locations that are exposed to direct sunlight and car headlights
Electric noise such as strong radios may enter the case may work.
Keep your wireless phone as far as possible.
If there is a shielding (include clear glass), the hidden person cannot be detected.
If you install it in high places or people still place it may not detect children or turn off the lights. Please understand the detection area and motion before determining the installation location.