Feature
●Set Includes: HT3.0 inches (75 mm) holder body + HT75 Frame CPL
●Adapter Ring: For 2.8 inches (72 mm) / 2.6 inches (67 mm) filter diameter (1 of each)
●Included parts: Screw for 2 holders, hex wrench, urethane for light shielding (replacement)
●Number of Filters Included: 3 pieces when shipped (2 pieces can be used by replacing the fixing screws on the filter slots)
Description
HT75 75mm Holder + CPL
Square filter holder outer frame for 75mm width and exclusive circular polarizing filter set.The holder is robust and precise and comfortable to operate.The included HT adapter ring comes with 2 types: 67mm and 72mm.Compatible with a wide range of lenses with various HT75 adapter rings sold separately for 39mm to 62mm.
The CPL effect can be adjusted with the gear on the frame of the included CPLIn addition, when using or without the CPL can be switched on or off the frame CPL.
How to use the frame CPL75mm (included)
Insert the entire metal frame into the filter holder slot just like a square filter.To prevent vignetting it is generally recommended to be installed in the front side (camera side) slot.The effect can be adjusted by turning the turning knob on the frame.Even if you change the angle of the holder when used with a variety of half ND filters, the effect can be re-adjusted independently on the frame CPL side.
How to use HT75mm Filter Holder
|
|
|
|
|
|---|---|---|---|
1. Choose the adapter that matches the lens filter diameterThe HT75 holder single piece and 75mm filter set come with an adapter ring for 67mm/72mm filter diameters, so you can choose the one according to your lens. If you want to use with smaller apertures, please purchase a variety of special adapter rings sold separately: 39mm/40.5mm/46mm/49mm/52mm/55mm/58mm/60mm(E60)/62mm. |
2. Attach adapter ring to lensAttach the ring you choose from 1. on your lens to the filter screw on the end of the lens. If your lens protection filter is installed, please take it off basically before attaching it. Wide angle lenses may cause vignetting and increase in filter quantities may cause image quality. |
3. Attach the outer frame of the holder (filter mount)When the outer edge of the attached adapter ring is hooked onto the nail on the outer frame of the holder, the adapter ring is pushed into while adding a nice knob on the holder outer frame. Spring integrates the adapter ring and the outer rim.The outer frame can be rotated freely after fixing. |
4. Install the square filterInsert the square filter into the slot of the holder.Insert the filter into the same slot on the left and right so that the filter side is parallel to the lens surface. Shipment can be used up to 3 pieces at the same time, but basically use them from the slot on the front side (lens side). Because the urethane used for light shielding is attached to the outer frame of the holder, it will be harder than other slots. |
|
|
|
|
|
|
|---|---|---|---|---|---|
| HT75mm Holder + CPL | Challenge Set, 3.0 inches (75 mm) | Starter Set, 3.0 inches (75 mm) | Standard Set II 3.0 inches (75 mm) | Railway Set 75mm | |
| Customer Reviews |
— | 2
| 1
| 1
| 1
|
| Price | ¥17,490 | ¥29,300 | ¥39,800 | ¥61,800 | ¥58,800 |
| HT75mm Holder + CPL | ○ | ○ | ○ | ○ | ○ |
| P. Soft GND 0.9 | - | - | - | - | ○ |
| P. Medium GND 0.9 | - | ○ | - | ○ | - |
| P. Hard GND 0.9 | - | - | - | - | ○ |
| P. Reverse GND 0.9 | - | - | - | ○ | ○ |
| P. Dual Purpose GND 0.75 | - | - | ○ | - | - |
| ND64 | - | - | - | ○ | - |
| ND1000 | - | - | ○ | ○ | - |